diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index ea9d49f2a911..d80da8f5d82d 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -2,6 +2,7 @@
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobinv7.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobinv7.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobinv7.dts
new file mode 100644
index 000000000000..6385b2488e45
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobinv7.dts
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board
+ * Copyright (C) 2016 Marvell
+ *
+ * Romain Perier <romain.perier@free-electrons.com>
+ *
+ */
+/*
+ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	model = "Globalscale Marvell ESPRESSOBin Board";
+	compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	vcc_sd_reg1: regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vcc_sd1";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		enable-active-high;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		red {
+			label = "espressobin:red:usr";
+			gpios = <&gpionb 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* J9 */
+&pcie0 {
+	status = "okay";
+};
+
+/* J6 */
+&sata {
+	status = "okay";
+};
+
+/* J1 */
+&sdhci1 {
+	wp-inverted;
+	bus-width = <4>;
+	cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
+	marvell,pad-type = "sd";
+	vqmmc-supply = <&vcc_sd_reg1>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		/*
+		 * Originally "winbond,w25q32dw", but since the manufacturer is known
+		 * to have replaced the part with "macronix,mx25u3235f" in some board
+		 * batches, just use the generic "jedec,spi-nor" and let the actual
+		 * chip type be probed. The partition table still depends on the chip
+		 * being 4 MiB in size.
+		 */
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		m25p,fast-read;
+		status = "okay";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0 0x3f0000>;
+			};
+
+			partition@3f0000 {
+				label = "ubootenv";
+				reg = <0x3f0000 0x10000>;
+			};
+		};
+	};
+};
+
+/* Exported on the micro USB connector J5 through an FTDI */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+/*
+ * Connector J17 and J18 expose a number of different features. Some pins are
+ * multiplexed. This is the case for instance for the following features:
+ * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
+ *   how to enable it. Beware that the signals are 1.8V TTL.
+ * - I2C
+ * - SPI
+ * - MMC
+ */
+
+/* J7 */
+&usb3 {
+	status = "okay";
+};
+
+/* J8 */
+&usb2 {
+	status = "okay";
+};
+
+&mdio {
+	switch0: switch0@1 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+
+		dsa,member = <0 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&eth0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan1";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan0";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "wan";
+				phy-handle = <&switch0phy2>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0@11 {
+				reg = <0x11>;
+			};
+			switch0phy1: switch0phy1@12 {
+				reg = <0x12>;
+			};
+			switch0phy2: switch0phy2@13 {
+				reg = <0x13>;
+			};
+		};
+	};
+};
+
+&eth0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};