* Switched RockPro64 to mainline u-boot
* Enabled rockusb and ums for RockPro64 in mainline u-boot
* Switched RockPro64 u-boot to TPL/SPL/BLOB scenario
* Enabled advanced recovery button support for RockPro64
* Disabled SDR104 mode for RockPro64 in legacy
The helios64 devicetree was submitted for inclusion in the mainline kernel.
The name used there is rk3399-kobol-helios64, so use the same here
for consistency, to be easily able to boot a mainline kernel without
changing the U-Boot environment and simplify further development.
* Switched Pinebook Pro to mainline u-boot
* Some Pinebook Pro mainline u-boot tweaks
(based on https://github.com/pcm720/u-boot-build-scripts)
* Removed Pinebook Pro legacy u-boot support
- Chanaged default x.org configuration to disable glamor
- Reintroduce patch to use DRM cursor plane as overlay in rk322x-current and -dev
- Updated wifi patches for kernel 5.8.10
- Bumped rk322x to u-boot v2020.07, removed reserved zones from device trees
- Updated OPTEE to v3.10, using ddrbin v1.10
- Bumped rk322x-current to kernel 5.8.y
- Imported new patches from knaerzche's LibreELEC fork for rk322x-dev (kernel 5.8.y)
- Adjusted existing patches to match changes, updated rk322x-dev kernel config file
- Add default modprobe conf file for esp8089 to force the crystal frequency to 40Mhz for rk322x targets
- Removed ssv6051 firmware packages to move to armbian-firmware repository
- Switching ssv6051-wifi.cfg to /lib/firmware for rk322x-legacy
- Removed P2P interface for esp8089 driver for rk322x-legacy
- Optimized ssv6051 performance: kernel module gains -Os flag, disabled p2p interface, enabled HW crypto for CCMP cipher
- Enabled remote control interface, IR GPIO kernel module and HDMI CEC modules
* Helios64: rework vdd_log and vdd_center
* helios64: Use rockchip binaries for legacy and current branch
Fully open source bootloader only on dev branch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* rework vdd_log and vdd_center patches
* Supress systemd service warning
* helios64: u-boot: staggered HDD power up
Set the delay to 10s in between turning on the next HDD power rails.
Remove the delay property from kernel device tree, let it only apply to
u-boot
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* helios64: fault LED as kernel panic indicator
also sync, u-boot dts
* helios64: fix hwmon udev rules
Legacy kernel (LK 4.4) has different class/naming on SoC Temp sensor.
Also fix typo on current/dev udev rules.
* Add initial Helios64 configuration
Add ethernet udev rules
Added disable auto power on script during shutdown
Configure ALSA to output audio to (DisplayPort) USB type-C
armbian-firstrun: exclude helios64 from generating fixed_mac
Each network interface on Helios64 already assigned to unique MAC
address in factory. Assigning Network Manager with cloned MAC is not
needed.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: rk3399: Add Helios64
Use rockchip propriettary loader
* kernel: rk3399-legacy: Update r8152 to support 2.5GbE USB RTL8156
Required for Helios64
* kernel: rk3399-legacy: update Rockchip PCIe driver
Port changes by ayufan on rockchip64.
* kernel: rk3399-legacy: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
Auto load lm75 modules
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: rework roc-rk3399-pc patch
the patch broken due to additional line added by helios64 on
arch/arm64/boot/dts/rockchip/Makefile
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: update Rockchip PCIe driver
Backport bugfix from mainline
refer to
https://patchwork.kernel.org/patch/11561979/
and
https://patchwork.kernel.org/patch/11561977/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rockchip64-current: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
* config: helios64: use mainline ATF on current branch
and u-boot TPL/SPL instead of Rockchip proprietary loader
* helios64: u-boot v2020.07 update
* Add Helios64 target
* kernel: rk3399-legacy: update Rockchip PCIe driver
Removed unrelated changes from porting ayufan fixes
Signed-off-by: Piotr Szczepanik <piter75@gmail.com>
* helios64: make use of PACKAGE_LIST* variables
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* Add initial support for Odroid N2+
* Update C4 config and test booting
* Updates to C4, N2, N2+
- merge C4 and N2 legacy under meson64, same u-boot
- upgrade legacy kernel to meed DTB from mainline
- merge N2 and N2+, add a hack to display + in motd when N2+ is detected
- shortly spin N2 fan at startup
- merged N2 mainline and legacy boot script
- add upstream patches
* One of the regulators were breaking booting of Odroid N2
Co-authored-by: Werner <EvilOlaf@users.noreply.github.com>
* WIP: Adding RockpiE config
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Mainline u-boot for ROCK Pi E
* Initial ROCK Pi E device tree in kernel
* Fixed supplies for ROCK Pi E device tree
* Adjusted u-boot load address for rockchip64 boards with 256MB eg. ROCK Pi E
* Blacklisted lima on ROCK Pi E
* Fixed ROCK Pi E patch after merge from master
* Removed mode settings from rk805 regulators
* Fixed issues with offloading for gigabit interface of RockPi E
* Adjusted ROCK Pi E board config
* Added dev branch for ROCK Pi E
* Add build targets
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Exchange legacy to current in ROCK Pi E build targets
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* Introducing Rockchip rk322x SoC support
Main features:
- Legacy kernel flavour based upon stable v2.x rk3288 Rockchip branch (https://github.com/rockchip-linux/kernel/tree/stable-4.4-rk3288-linux-v2.x)
- Current kernel flavour based on mainline 5.6.y kernel
- Mainline u-boot (v2020.04)
- Single generic tv box target (rk322x-box) which boots on all the known tv boxes
- Hardware devices (eMMC/NAND, led wiring configuration, SoC variant selection) modulation done by user at runtime via device tree overlays - a script (rk322x-config) is provided for autodetection and simple configuration by inexperienced users;
- Bits added to armbian-hardware-optimization to set affinity for irq handlers
- rk322x-box targets already added to targets.conf for automatic image creation
* Removed disabled patches
* Restored mysteriously removed comment character
* For xt-q8l-v10 rk3288 board:
- Upgraded u-boot to v2020.04, reworked configuration to match new version, enabled HDMI video console
- Increased u-boot boot delay from 0 seconds to 1 second for rockchip boards, to allow user interrupt u-boot boot process
- Imported efuse rk3288 driver into u-boot, made ethernet address stable using soc serial
- Upgraded ddrbin loader to v1.08
- Added VDSO patch for rockchip-current and rockchip-dev kernels for clock_gettime64 to fix erratic clock on 32 bit ARM devices with recent glibc
- Disabled 600 Mhz OPP node for GPU due to Panfrost instabilities, thus enabled 500 Mhz node
- Various fixes and enhancements to xt-q8l-v10 device trees for current and dev targets
- Added (disabled) u-boot HDMI patch for Tinkerboard
* Removed rk3288 ddrbin v1.08 from rockchip blobs, changed reference to use rkbin-tools repository
* Removed unneeded disabled patch for tinkerboard HDMI
odroidc1 can fail to boot probably depending
on features of the ext4 rootfs that is created
during the build process
serial log error:
Loading file "/boot/uInitrd" from mmc device 0:1 xxa1
invalid extent block
since there is no support for that board in upstream u-boot
backport the patch from
upstream commit:b5bbac1a9b07016602559ff483df265fef6c1f83
see also [1]
[1] https://lists.denx.de/pipermail/u-boot/2014-January/170802.html
Signed-off-by: Dirk Neukirchen <plntyk.arm@plntyk.name>
* meson-sm1: use amlogic-boot-fip to generate boot binary for SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* patch: add Linux and U-Boot patches
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* configs: enable Odroid-C4
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* Disable DE2 in u-boot to improve EDID detection
* Remove deprecated patches
* Define BOOTBRANCH in top level
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Sunvell R69: cpu voltage regulator (re-)added - dram clock reduced.
CPU regulator (re-)added to u-boot and kernel dts - the box will not boot without it.
Dram clock reduced in defconfig to increase stability.
[AR-85]
* Updated rockchip64-dev to u-boot v2019.10 and BL31 v1.30 (rk3399 boards)
* Updated rk3399 to u-boot v2019.10 and BL31 v1.30
* Revert changes to renegade u-boot patches
* Moved renegade u-boot patches into board dir
* Added debug info for RockPro64 and switched sdmmc to fifo-mode
* Disabled regulators in SPL for RockPro64
* Re-enabled sd vcc regulator in SPL for RockPro64
* Some device tree and config changes for OrangePi RK3399
* Fixed Rock Pi 4A's $BOOTCONFIG
* Let some boards use mainline atf instead of the one in rkbin
For example, roc-rk3399-pc can just boot the kernel using the
mainline atf.
* Add roc-rk3399-pc
* Fixed reset in mainline ATF
* Attached ATF version to v2.2 tag
* WIP: sdmmc fifo-mode in SPL only
* Renamed source config files
* Reverted changes to rockchip64 sources config
* Reverted patch moves
* Add missing trust.ini patch to rk3399 u-boot
* Reinstated tpl/spl patches in rk3399 family
* Added $RKBIN_DIR prefix in rk3399 sources
* Add demonstration of boards bootloader assignment in rk3399
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
* Fix wifi
patch "board-h2plus-nanopi-duo-add-device.patch": increase post-power-on-delay-ms from 50ms to 200ms in wifi_pwrseq node in nanopi-duo dts [dev-branch].
Change in line with other XRADIO device trees (orange pi zero, sunvell).
See also Pull Request #1605.
* Fix xradio patch (dev-branch)
fix KConfig to 5.x - WLAN_VENDOR-flag set to "y" in line with other drivers - otherwise module not loaded.
* correct device name
change nodes "model" and "compatible" to correct device name (from "NanoPi Duo AIR" to "NanoPi Duo") [dev-branch]
Not functionally necessary, but more correct.
* Initial commit for serial consoles rfc
* Board configuration cleanup + small tweaks
* Add serial gadget rename to dev kernel as well
* Cleanup, fixing permissions
* Cleanup board configs
* Initial commit for FA ZeroPi.
* Tested for building.
* Adjust few bugs.
* Move to WIP since its not tested on hardware yet.
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Changed BOARDFAMILY from mx7dsabre to imx7d
Change-Id: Id351c9f6a8c907b415b804bfe11b86027278ed86
* Disabled MD driver for imx7d Kernel
MD driver does not work correctly on NXP-modified kernel
Change-Id: I58e8de6ee0b99282c452f594e22f6f7e1ff59ae0
* Added ALSA configuration bits for rk3288 HDMI and SPDIF to allow
pulseaudio show proper sound device/profile/mapping names instead of
just "Built-in Audio" for all of them
* Added ALSA device description in asound.conf to provide correct labels for PulseAudio for RK3288 devices when SPDIF and DW-I2S-HDMI simple audio cards are exposed
Removed unnecessary ALSA configuration files previously added from rockchip.conf
* Fixed cpu operating points tables and raised a bit (+5°C) cooling for non-critical temperatures for xt-q8l-v10 in dev and next kernel flavours
* Fixed again cpu opp table
* Removed whole cpu opp table and retouch only necessary operating points
* Enabled gpiomem driver for xt-q8l-v10 in next kernel flavour
* Added debounce delay and card detect gpio pins for sdmmc card holder for xt-q8l-v10 board
* Added card-detect and debounce delay for sdmmc for xt-q8l-v10 board in next kernel flavour too
* Fixed missing comment in xt-q8l-v10 device tree patch
* Added gpiomem to xt-q8l-v10 board for dev kernel
* Fixed FAN53555/Silergy patches to accomodate changes in u-boot v2019.04
* Changed property property flags for USB regulators in u-boot and kernel: kernel is now informed that bootloader is going to turn the USB power on
* Removed assert-phy-reset-when-waking-up-in-rk3288-platform patch due to inclusion in mainline 5.2 kernel
Reenabled ARM-DTSI-rk3288-add-usbphy-reset patch to include USB PHY reset lines to all rk3288 devices
* Removed ARM-DTSI-rk3288-add-usbphy-reset.patch due to inclusion in mainline kernel 5.2
* Initial Mvebu RFC https://github.com/armbian/build/issues/1426
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu: add missing patches
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu: change making u-boot targets to standard way, adjust patches and config
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* helios4: set default branch to use U-Boot 2018.11
Switch over to U-Boot 2018.11 that has been used for some time in next
branch.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: Enable DEV branch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: Add RTC support on Clearfog and Helios4
Added DM driver for mvebu RTC and enable it on Clearfog and Helios4
configuration.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* add boot-marvell.cmd backward compatibility
The patches added missing variable that used on boot-marvell.cmd and
also adjust the some memory addresses to prevent crash due to usage of
fdt_high and initrd_high.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* helios4: Added SPI NOR flash target
Build bootable SPI NOR flash image.
Change the boot order to USB -> SATA -> MMC
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* Restore SPI support on U-Boot 2019.04
* mvebu: kernel: Added Wake-On-GPIO and WoL support
The patch set was missing during transition.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* [#1429] SolidRun's ARMADA A388 SOM U-Boot ODT Update
Old versions of U-Boot did not configure correctly the ODT on data
signals of DDR RAM on SolidRun's ARMADA A388 SOMs.
According to SolidRun Knowledge Base, the changes already pushed to
mainline U-Boot. But then it was overwritten when Marvell DDR Training
Tool updated
[URL]
https://developer.solid-run.com/knowledge-base/armada-38x-som-u-boot-odt-update/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* [#1429] mvebu: u-boot: Add revision id for Armada 38x B0
Added patch for SolidRun U-Boot v2018.01 and
for Helios4 U-Boot v2018.11
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* clearfog: Added SPI NOR flash target
Build bootable SPI NOR flash image.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: clearfog: DEV branch use mainline U-Boot
Also move clearfog base patch into its own board folder.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: enable U-Boot uart target
Normal MMC image can be used for uart boot using following command:
./tools/kwboot -b u-boot-spl.kwb /dev/ttyUSBX
But on Helios4, the SPL failed to continue the booting process if ECC is
enabled, so disable it.
Since the usage of uart boot is more for rescue/debug, disable autoboot.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: NEXT branch use mainline U-Boot
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: fix fancontrol related bug during buster testing
- On kernel 4.19, cpu thermal sensor changed the name from
armada_thermal into f10e4078.thermal. Added this new name to udev rules
- Since DEFAULT branch now use kernel 4.14, update fancontrol
configuration
- Load lm75 kernel module
- On kernel 4.19, cpu temp reading about 20 degree C lower, update
fancontrol configuration.
[URL]
https://forum.armbian.com/topic/10214-clearfogpro-possible-change-in-temperature-reporting-between-414next-and-419dev
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: Override vendor provided fancontrol unit
systemd emit following message on dmesg
systemd[1]: /lib/systemd/system/fancontrol.service:9: PIDFile=
references path below legacy directory /var/run/, updating
/var/run/fancontrol.pid \xe2\x86\x92 /run/fancontrol.pid; please update
the unit file accordingly.
Override and change the value in the unit file to remove the message.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: DEV branch use its own u-boot patch folder
The patches are copied over from u-boot-mvebu-next
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: u-boot: Make clearfog model distinction more obvious
While at it, also change SerDes LANE4 into USB 3.0 on Clearfog Base.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* lib: Use apt-get install instead of dpkg on install_deb_chroot()
dpkg -i does not install dependencies required by the package.
This is needed if the BSP package requires other package that is not
installed during debootstrap.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: mvebu: helios4: Move various tweak to family_tweak_bsp()
Various tweak in family_tweaks_s() only applied to SD card image.
Move it to family_tweaks_bsp() so it will also included on the BSP
package and applied to existing user.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: mvebu: helios4: Add /etc/modules to BSP
On kernel 4.19, user need to modify the /etc/modules to add lm75 kernel
module. Pack the file into BSP so user no longer needed to modify it.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: kernel: Make zbud as built-in module
To remove the following error:
[ 1.705485] zswap: default zpool zbud not available
[ 1.705488] zswap: pool creation failed
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* bootscripts: mvebu: Add default value for spi_workaround
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: kernel: Backport armada_thermal changes to 4.14 (#1452)
On kernel 4.19, armada_thermal driver has been fixed to address
Marvell's Errata #132698 (The changes first appear on LK 4.16). The
result is temperature reading is around 20 degree Celsius lower.
Currently armbian-motd apply -20C tweak for both LK 4.14 and LK 4.19
which is incorrect. Instead of adding some logic on what condition to
apply the tweak, it is better to remove the tweak and patch the kernel
instead.
Revert commit b3dd4e9 ("[ mvebu ] Put back Armada temperature tweak in
motd")
which is part of #1421 solution.
[URL]
https://forum.armbian.com/topic/10214-clearfogpro-possible-change-in-temperature-reporting-between-414next-and-419dev/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: unified fancontrol config
Since LK 4.14 on DEFAULT branch already patched and the temp reading is
same as LK 4.19 on NEXT branch, it is no longer needed to separate
fancontrol configuration file.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: helios4: Remove rev id patch
The patch is already applied in helios4 repo, no need to have it in
armbian.
This revert helios4 part of commit 7411c55
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: clearfog: enable PCIe support and PCIe reset
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: clearfog: add boot-marvell.cmd backward compatibility
The patches added missing variable that used on boot-marvell.cmd and
also adjust the some memory addresses to prevent crash due to usage of
fdt_high and initrd_high.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu: helios4: tweak regarding temperature setting
Make fan speed similar compared to pre-patched armada-thermal. Target
PWM value around 70 during idle.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: sources: clearfog to use u-boot 2018.01 for NEXT branch
This changes also affect Helios4. Moved the shared U-Boot source setting
back to Helios4 for NEXT branch.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* config: boards: build Stretch image for Clearfog and Helios4
Also remove DEV from Helios4 CLI_TARGET
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: mvebu-next: Disable access to SPI Flash
User need to set spi_workaround=yes to enable SPI Flash access and lost
access to internal SATA.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu-next: adjust kernel config
* mvebu-dev: bump to 5.2 and adjust kernel configuraion. Tested for building.
* Adjust kernel config, add AUFS
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* mvebu-next: Adjust kernel config, add debug GPIO
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* mvebu-dev: separate Clearfog Base U-boot configuration file and patch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
The eMMC must have been forgotten when the device tree for the NanoPi Neo Air was being added to mainline u-boot, which results in the device being unable to boot when installed to the internal eMMC using the nand-sata-install utility.
