* VENDOR, rock-pi-n10, RM_LIST for armbian-config/zsh
VENDOR parameter in configuration
zsh is the best of course...
Static MAC for networkd
ROCK Pi N10 (Radxa) - Initial support, knwon bugs:
- Problem with poweroff (kernel panic).
- DeviceTree is not fully verified, I suspect missing and unnecessary
entries.
- No support for NPU
- u-boot without NVME support
- I have doubts if I chose the right preboot loader for RK3399Pro, NPU
and installed DDR memory.
* New RK3399Pro boot preloaders.
* rootfs checksum, DEBOOTSTRAP_LIST fix, output.log fix
Repaired checksum for rootfs
Added use PACKAGE_LIST_RM to purge DEBOOTSTRAP_LIST
Better logging to output.log
Fix for new host distribution detection (ie Debian Bullseye).
ubootdebs as new cleaning option
* Add initial Helios64 configuration
Add ethernet udev rules
Added disable auto power on script during shutdown
Configure ALSA to output audio to (DisplayPort) USB type-C
armbian-firstrun: exclude helios64 from generating fixed_mac
Each network interface on Helios64 already assigned to unique MAC
address in factory. Assigning Network Manager with cloned MAC is not
needed.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: rk3399: Add Helios64
Use rockchip propriettary loader
* kernel: rk3399-legacy: Update r8152 to support 2.5GbE USB RTL8156
Required for Helios64
* kernel: rk3399-legacy: update Rockchip PCIe driver
Port changes by ayufan on rockchip64.
* kernel: rk3399-legacy: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
Auto load lm75 modules
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: rework roc-rk3399-pc patch
the patch broken due to additional line added by helios64 on
arch/arm64/boot/dts/rockchip/Makefile
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: update Rockchip PCIe driver
Backport bugfix from mainline
refer to
https://patchwork.kernel.org/patch/11561979/
and
https://patchwork.kernel.org/patch/11561977/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rockchip64-current: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
* config: helios64: use mainline ATF on current branch
and u-boot TPL/SPL instead of Rockchip proprietary loader
* helios64: u-boot v2020.07 update
* Add Helios64 target
* kernel: rk3399-legacy: update Rockchip PCIe driver
Removed unrelated changes from porting ayufan fixes
Signed-off-by: Piotr Szczepanik <piter75@gmail.com>
* helios64: make use of PACKAGE_LIST* variables
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
* Initial commit BPi R2:
Currently working/not working:
- u-boot:
- builds with minor issues
- patching and cleanup happens on 'https://github.com/chwe17/u-boot-mt'
- next (https://github.com/frank-w/BPI-R2-4.14)
- boots with minor issues
- ETH doesn't work with nm
- sata works
- no wifi (needs driver from: https://github.com/frank-w/BPI-R2-4.4)
- USB not working (xhci-mtk 1a1c0000.usb: fail to get vbus) needs investigation
- appended device tree is needed due to u-boot doesn't work with fdt (kernelpacking needs adjustemts e.g. cat zImage dtb > zImage-dtb
- dev (kernel.org master)
- untested, needs adjustments in config (e.g. CONFIG_LOCALVERSION="")
- since no defconfig is available config is based on frank-w 4.16 Kernel
- Kernel builds without issues
- manual packing of kernel and dtb similar to next
The board boots, serial console is available but everything else must be expected as not working!
- to do:
- u-boot needs a cleanup
- binary blobs needs investigation
- eMMC is **not tested** and needs for sure adjustements! (don't try nand-sata-install!!!)
- bootscript isn't tested (only manual boot over u-boot console at the moment)
- both kernelconfigs aren't 'armbian standard' modules need to be adjusted
Only use it when you know're familiar with u-boot commands!
* Small fixes, add bootscript
- add bootscript for patched u-boot (needs patching of u-boot, currently under investigation and not working properly)
- revert cat zImage dtb > zImage-dtb (cause not working)
- first cleanup of dev kernelconfig (remove CONFIG_LOCALVERSION="")
* Minor fixup
-kernelconfig for next was adjustet so that USB is recognized
-firt bootscripts was written to boot with source command (doesn't work 100% reliable)
-slightly adjustd boardconfig (e.g. bootscript)
must still be considered as early wip!
* small update (FDT works now)
-working bootscript
-adjusted boardconfig
-earlyprintk activated in kernelconfig
* First attempt to get ETH working
-all interfaces are bridged together
-performance sucks at the moment (not clear if it's related to insane network configuration or I miss something obvious... :P )
* Major update (see below for changes):
- 4.14 kernel was dropped due to https://forum.armbian.com/topic/7296-bananapi-r2-csc-mt7623-as-new-boardfamily/?do=findComment&comment=55194 and following
- boot.cmd was adjusted to 'clean' mainline behaviour
- next build opition and its defaultconfg was removed (at the moment dev only)
- rework of the network default configuration
- default configuration will be over network.d **not** NetworkManager
- per default all wired interfaces are bridged together to br0 (still wip)
- old 'interfaces' configuration was removed
- boardconfig is adjusted (no desktop until I've prove that HDMI works)
- what works/ not works:
- board boots up without manual u-boot hacking
- SATA, USB3 (massstorage) is tested and works without issues
- due to rework of network configuration this is still wip and must be considered as 'not working'
* moved to network.d for configuration of wired network
- renamed bsp packages
- blacklist wired interfaces for NetworkManager
- defined all wired interfaces as br0 in systemd/network
- defined networkd als default renderer for bionic (not tested yet!)
* The houskeeping commit:
- BOARDFAMILY was renamed to mt7623 instead of mt7623n (including patchfolders etc.)
- Network.d has no fully control over wired networkes (block NM from controll, start networkd on firstrun etc.)
- Further cleanup kernelconfig
- CPU temp is visible from userspace
- missed switch driver loaded
- cryptodrivers are there (not tested)
- still a bunch of work
* Add DMA mem alloc patch
-under testing!
* Add next option (4.17.y) stick dev to master (4.18-rc1 untested)
* minor fixes:
- solve kconfig issues between 4.17 and 4.18
- stick next branch to 4.18
- first attempts to bring up gmac2 (doesn't work currently)
* switch to upstream u-boot
- fix ext4 dependency in patch series
- kernelpacking currently broken
* add bootz & cmd_ext4
* resolved merge conflict
* apply ugly u-boot patch, fix bootscript
* remove unneeded stuff, apply forgotten stuff
* update config for dev & clean up boardconf (remove xenial)
* - drop dev and next, move into default. There is no intention to provide stock kernel
- fixed board description, renamed to WIP, where it can be merged later
- packing boot firmware to the u-boot package
- docker dependencies (aufs will be added later. not essential)
- attached to 4.19.y
- loading armbianEnv.txt
- UUID support (tested)
- enabled ZRAM (tested)
- enabled eMMC install (not quite working properly yet)
- Bionic has some issues with systemd networking.
* gov to ondemand (thermals are conservative anyway), remove unneeded kernelconfigs
* Added AUFS, remove debug from kernel boot parameters, add ath10 mPCI support (which works)
* add power-off-key and rtc
* Added onboard wireless, but it's enabling is disabled by default. Too fragile.
* Change to CSC target
* Basic armbian services RFC
- tested building and upgrade
- armbian-optimize-hardware and armbian-setup-hardware have still the same content
* fix permissions
* Forther renaming and small fixes
* Odroid C2 NEXT tiny config adjustement to remove errros from bootup and moving u-boot to 2018.05
* More cleanings
* permissions fix
* More cleanup ...
* permi
* Remove few Ubuntu related things, fix permissions
* Further mini improvements
* Fix logrotate compression and permission issues
* Bugfix
* Wrong services setup at package install. fixing
* RAM logging: workaround for older kernel/btrfs driver versions
* Renaming services, proper config for zram, few bugfixes.
* Various fixes
* Various fixes
* No $TMPFILE needed here
* Various fixes
* Lower this so boards with low memory can use it too
* Various fixes
* Adjust logfile to armbian-hardware-monitor.log
* Remove swap file creation
* Fix permissions in all logrotate configs if needed.
* Prevent loading parallel printer port drivers which we don't need here.
