* Rename add-board-roc-pc.patch to add-board-rk3328-roc-pc.patch
there are a large number of "roc-pc" boards as firefly has adopted/misapplied the Libre Computer naming convention. Be as specific as possible.
ALSO NOTE A DTS EXISTS IN MAINLINE.
This patch is overwriting the mainline DTS entirely, and should be replaced with patches changing the mainline instead to avoid further deviation from the base.
* Rename add-board-roc-pc.patch to add-board-rk3328-roc-pc.patch
Specify which roc-pc it is
This patch doesn't make any changes to the source file:
- rockchip->ep_gpio = devm_gpiod_get_optional(dev, "ep",
- GPIOD_OUT_HIGH);
+ rockchip->ep_gpio = devm_gpiod_get_optional(dev, "ep", GPIOD_OUT_HIGH);
- this patch had "half-mbox" formatting
- first a bare patch (no mbox headers, From/Subject etc)
- then an mbox-formatted patch
- this causes the 1st/bare patch to be lost when parsing this file with a proper mbox-enabled tool
* `meson64-6.1` - rebased patches; 3 were mainlined
- JetHub device was mainlined
- ODROID's hack for pwm1_enable was re-done diffrently in mainline
* `meson64`: switch `current` to `6.0`, `edge` to `6.1-rc8`
- notes in the board file about the RAM issues (tested, confirmed working blob change of #4383 by @pinhaozhang working with u-boot 21.07; `blobless` also works with ATF v2.7 on my known-good-RAM boards)
- tinkerboard-2: add full firmware, for the rtl8822ce PCIe Wifi default card in the tb2 as shipped by ASUS
- tinkerboard-2: uboot: rename `TARGET_TINKER-2_RK3399` to `TARGET_TINKER2_RK3399` to avoid warnings all over
- tinkerboard-2: slower but working Tinkerboard 2S eMMC (HS400+ES to HS200)
- both for u-boot and kernel.
- should not affect 2, only 2S
* `meson64`: `6.0`: g12a and g12b pinmux patches from Radxa
* u-boot: `radxa-zero2`: Radxa's patches for the Zero2 on `v2022.10`
* u-boot: `radxa-zero2`: use `v2022.10` plus Radxa's patches
* `meson64` u-boot v2022.10: change `BOOT_TARGET_DEVICES` to try to boot USB, NVME and SCSI before SD, MMC, PXE, DHCP
* `radxa-zero`: include v2022.10 standard patches (eg: boot from USB first)
* `radxa-zero` & `radxa-zero2`: set `BOOT_FDT_FILE` explicitly; no real changes
* `radxa-zero2`: `6.0`/`edge`: update Radxa Zero 2 DTS patch with Radxa's latest
* `radxa-zero`: `6.0`/`edge`: update USB-C patch with "fix interrupt storm from fusb302"
* `radxa-zero`: use pure mainline v2022.10 u-boot with no patches
* Add Rockpi 4C+
* add newer patches:
- apply patches from RadxaNaoki <noaki@radxa.com>
- ref 5652d6f9c2a4e2c50ac1040c0388859381b0616f: arm64: dts: rockchip: add gmac for ROCK 4C+ (#17)
- apply latest patches from Marcone <marco.nelissen@gmail.com>
- ref e39da181b099a86f5440ed1c08fc699d4a65aed7: arm64: dts: rockchip: Make Rock Pi 4C+ ethernet actually work
- ref 8c519612eeb852268371b3c596eec4622460e5bf: arm64: dts: rockchip: add Rock Pi 4C+ LEDs
- ref 726441afe687ea6059bac37f145ff204b75430f7: arm64: dts: rockchip: enable Rock Pi 4C+ wifi
- ref caad7bef3b5558e2598480c0a0089e2ac3cedcdd: arm64: dts: rockchip: enable Rock Pi 4C+ nvme
- ref 6cdc3215d1691bcd2a407a30e88efa0cec179eb2: arm64: dts: rockchip: enable Rock Pi 4C+ OTG
* default top USB3 port to host mode
* get 2nd HDMI port to work at least. :)
* revert OTG USB3.1 port back to otg mode
* [rockpi4c+] update board def. add usb host overlay.
* remove redundant HDMI clocks and voltages
* enable test builds for Rock PI 4 C+
* [rockpi4c+] add USB host overlay
Co-authored-by: Joe Khoobyar <fourheads@gmail.com>
