* Initial commit BPi R2:
Currently working/not working:
- u-boot:
- builds with minor issues
- patching and cleanup happens on 'https://github.com/chwe17/u-boot-mt'
- next (https://github.com/frank-w/BPI-R2-4.14)
- boots with minor issues
- ETH doesn't work with nm
- sata works
- no wifi (needs driver from: https://github.com/frank-w/BPI-R2-4.4)
- USB not working (xhci-mtk 1a1c0000.usb: fail to get vbus) needs investigation
- appended device tree is needed due to u-boot doesn't work with fdt (kernelpacking needs adjustemts e.g. cat zImage dtb > zImage-dtb
- dev (kernel.org master)
- untested, needs adjustments in config (e.g. CONFIG_LOCALVERSION="")
- since no defconfig is available config is based on frank-w 4.16 Kernel
- Kernel builds without issues
- manual packing of kernel and dtb similar to next
The board boots, serial console is available but everything else must be expected as not working!
- to do:
- u-boot needs a cleanup
- binary blobs needs investigation
- eMMC is **not tested** and needs for sure adjustements! (don't try nand-sata-install!!!)
- bootscript isn't tested (only manual boot over u-boot console at the moment)
- both kernelconfigs aren't 'armbian standard' modules need to be adjusted
Only use it when you know're familiar with u-boot commands!
* Small fixes, add bootscript
- add bootscript for patched u-boot (needs patching of u-boot, currently under investigation and not working properly)
- revert cat zImage dtb > zImage-dtb (cause not working)
- first cleanup of dev kernelconfig (remove CONFIG_LOCALVERSION="")
* Minor fixup
-kernelconfig for next was adjustet so that USB is recognized
-firt bootscripts was written to boot with source command (doesn't work 100% reliable)
-slightly adjustd boardconfig (e.g. bootscript)
must still be considered as early wip!
* small update (FDT works now)
-working bootscript
-adjusted boardconfig
-earlyprintk activated in kernelconfig
* First attempt to get ETH working
-all interfaces are bridged together
-performance sucks at the moment (not clear if it's related to insane network configuration or I miss something obvious... :P )
* Major update (see below for changes):
- 4.14 kernel was dropped due to https://forum.armbian.com/topic/7296-bananapi-r2-csc-mt7623-as-new-boardfamily/?do=findComment&comment=55194 and following
- boot.cmd was adjusted to 'clean' mainline behaviour
- next build opition and its defaultconfg was removed (at the moment dev only)
- rework of the network default configuration
- default configuration will be over network.d **not** NetworkManager
- per default all wired interfaces are bridged together to br0 (still wip)
- old 'interfaces' configuration was removed
- boardconfig is adjusted (no desktop until I've prove that HDMI works)
- what works/ not works:
- board boots up without manual u-boot hacking
- SATA, USB3 (massstorage) is tested and works without issues
- due to rework of network configuration this is still wip and must be considered as 'not working'
* moved to network.d for configuration of wired network
- renamed bsp packages
- blacklist wired interfaces for NetworkManager
- defined all wired interfaces as br0 in systemd/network
- defined networkd als default renderer for bionic (not tested yet!)
* The houskeeping commit:
- BOARDFAMILY was renamed to mt7623 instead of mt7623n (including patchfolders etc.)
- Network.d has no fully control over wired networkes (block NM from controll, start networkd on firstrun etc.)
- Further cleanup kernelconfig
- CPU temp is visible from userspace
- missed switch driver loaded
- cryptodrivers are there (not tested)
- still a bunch of work
* Add DMA mem alloc patch
-under testing!
* Add next option (4.17.y) stick dev to master (4.18-rc1 untested)
* minor fixes:
- solve kconfig issues between 4.17 and 4.18
- stick next branch to 4.18
- first attempts to bring up gmac2 (doesn't work currently)
* switch to upstream u-boot
- fix ext4 dependency in patch series
- kernelpacking currently broken
* add bootz & cmd_ext4
* resolved merge conflict
* apply ugly u-boot patch, fix bootscript
* remove unneeded stuff, apply forgotten stuff
* update config for dev & clean up boardconf (remove xenial)
* - drop dev and next, move into default. There is no intention to provide stock kernel
- fixed board description, renamed to WIP, where it can be merged later
- packing boot firmware to the u-boot package
- docker dependencies (aufs will be added later. not essential)
- attached to 4.19.y
- loading armbianEnv.txt
- UUID support (tested)
- enabled ZRAM (tested)
- enabled eMMC install (not quite working properly yet)
- Bionic has some issues with systemd networking.
* gov to ondemand (thermals are conservative anyway), remove unneeded kernelconfigs
* Added AUFS, remove debug from kernel boot parameters, add ath10 mPCI support (which works)
* add power-off-key and rtc
* Added onboard wireless, but it's enabling is disabled by default. Too fragile.
* Change to CSC target
Adds preliminary patches for 4.19
Known Issues:
- Does not like a lot of HDMI adapters
Needs tested by anyone with a Le Potato, Odroid C2, or Nanopi K2
- update patchset to reflect @superna9999 's meta-meson patches
- notable update adds video decoder and canvas drivers
As always many thanks to BayLibre and Neil Armstrong
This change brings in the Rockchip version of the FUSB302 USB controller driver into
the kernel (with appropriate changes to enable it to build in kernel 4.19.y), and
configures the module build for the rk3399 kernel. This provides proper operation
of all <&fusb0> "extcon" references for the rk3399-nanopi4 boards, thereby enabling
all board USB host ports (e.g., now including <&u2phy0>) to now function properly.
- Fixes horrible screen performance/long boot/etc
- Thank you @Miouyouyou
Current issues:
- No Pulse Audio. Probably related to the I2S issues, needs checked
- General config review needed
- Seems to be topping out at 1.6 GHz
- only known bug so far: Somehow the entire screen has been rotated 180 degrees, making the touch screen not align with the graphics (can rotate in settings)
- probably an easy fix, but finished for tonight.
* Bump to 4.18, removing the obvious, fixing build problems, put some on waiting.
* Pin 4.18 to DEV, rollback 4.14 to NEXT, adjust configs, remove one deprecated patch from NEXT and add board-h3-address-some-stability-issues.patch
* Adjust few boards in development to new reality, removing it from NEXT for now
* Adjust few board configs
* Board config adjustement
* Adjust few boards configs
* Port NeoCore2 and Neo21.1 to 4.14.y
* Adjust board config
* Adjust board config
-- Thanks again to @ntemis for bringing these together and letting me know about it
- Tinker reboot now seemingly solved by a proper method, should no longer require OF workarounds
- various fixes from various sources, see patches for complete information.
- boots, still needs debugging of BT/touchscreen/sound
- some patch warnings exist, again WIP update for those willing to take a look. (@chwe17 perhaps?)
Based on work of David Huang https://github.com/hjc4869 Changed in the transition:
- firefly family was renamed to rk3399, which we actually never started to use. It was made for Odroid N1, which will never be sold
- adjusted compiler toolchain2 parameter
- added standard wireless drivers
- kernel config with the following changes: Docker dependencies, ZRAM, CPUfreq info, ...
- added upstream patches
- made test Ubuntu Bionic desktop and CLI Stretch build, bootlog: http://ix.io/1jVu
TBD: wifi and BT support, mainline kernel, ...
There are two versions of the NanoPi NEO2 board; this change adds the default DT for the
v1.1 board. It includes the correct LED configuration and the MP2143DJ VDD regulator
definition.
This change introduces an optional overlay that can be used to modify
the default CPU clock operating table to support a maximum core clock
of 1.4GHz. These higher clock rates will only be allowed if the
board's CPU VDD regulator can support operation at 1.4v (or greater),
e.g., SY8106A.
This change adds a board configuration for the NanoPi NEO Core2 LTS device ("nanopineocore2").
This board configuration provides support for the Core2's SY8106A I2C-based voltage regulator.
This regulator provides higher CPU voltage operation, allowing higher CPU clock rates to be
utilized.
* [Early WIP] Update sunxi-next to kernel 4.17
* Switch Allwinner 32 and 64bit to U-boot 2018.05
* Adjust patched for 4.17.y / sunxi-next
- adjust both configurations
- removing FAT support from u-boot (breaks if you try to save)
Tested those boards:
Cubietruck: wlan fails http://ix.io/1fYS USB OK, HDMI yes
Bananapi R40: http://ix.io/1fZm USB OK, HDMI yes
Lime A64: USB no, HDMI no, wireless buggy, eMMC yes
Orangepi prime H5: OK http://ix.io/1fZJ DVFS no
Orangepi2e: DVFS OK, HDMI OK, net OK, wifi OK, eMMC ok, http://ix.io/1fZT
* Kernel config update, enabling HDMI on CT+
* Trying to fix A64 HDMI but failed. Fixed M64 ethernet instead
* Update orangepioneplus.wip
* Update orangepioneplus.wip
* Fix H6 build process
* Add regulator bits for Orangepizero+, thanks to @5kft
* add H5 support for optional 1.3v regulator and 1.3GHz operation
This patch adds two optional overlays that can be used to:
1) enable the 1.1v/1.3v regulator on boards that provide the necessary compatible H/W support
2) modify the default CPU clock operating table to add new 1.2GHz and 1.3GHz clocks
Note that the generated regulator overlay will only support boards whose 1.1v/1.3v regulator
is controlled by GPIO PL6.
* updates for the NanoPi NEO Plus2
This change introduces a patch that provides two changes for the NanoPi NEO Plus2:
* Configure the "cpu0" to use the "vdd_cpux" regulator; this enables the ability to use higher CPU clocks
* Correct the configurations of the on-board power and status LEDs
* Adjust nightly building and few boards config cleanup
* implemented improved support for the FriendlyArm NanoPi Fire3
* introduced new WIP board configuration "nanopifire3"
* added and enabled the FA SPU1705 regulator
* enabled CPU-based thermal support
* implemented DT-based DVFS table (400MHz-1.4GHz)
* fixed and updated the thermal table and cooling maps
* added support for the onboard LED
* minor patch cleanup
