- allows users to put .dts files bare in `userpatches/kernel/rk35xx-legacy/dt`
- important: everyone is still invited to send the DTs to https://github.com/armbian/linux-rockchip directly
- where yes, they'll have to patch the Makefile there as normal
* meson-s4t7: bump u-boot to khadas-vims-u-boot-2019.01-v1.6-release
* Use khadas default bootargs as much as possible
* Add new hook to allow copying code into kernel
* meson-s4t7: legacy: Switch to 5.15 kernel
* meson-s4t7: add kernel-config for 5.15 kernel
* device tree overlays for 5.15 kernel for vim1s and vim4
* restructure packaging of bsp files for vim1s/vim4
* silence vblank warning on boot
* Remove display workaround as it doesn't work with 5.15 kernel
* Remove 5.4 kernel patches
* add salvas UHS overlay and enable on 2 known devices known to have voltage regulator needed to leverage UHS
* remove increased UHS from pinebook-pro default due to justification in kernel commit history
* remove enabling YOLO UHS overlay from default board config
In my initial commit I assumed CONFIG_USE_PREBOOT=y was enabled
by default. I was wrong.
As reported by MicroLinux (Salva) on DISCORD the unit was still
having issues booting. I sent him a patch I use which enables
preboot and he reported back that "It boots fine now".
NOTES: The patch he tested also had boot logo support enabled. In
my testing boot logo support is not required. If for some reason
in the future there are still eMMC boot issues, than maybe adding
a slight delay "sleep 2" to preboot would suffice.
https://github.com/armbian/build/pull/5858
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
* rockchip64: Add board "ASUS Tinker-Edge-R"
* rockchip64: Add board "ASUS Tinker-Edge-R": hammer for 6.6 current & 6.7 edge
- cleanup
- squash dtsi and dt into a single thing, rename to dashes
- change dtb reference in board file
- drop the 6.1 patch that has junk in it
---------
Co-authored-by: Ricardo Pardini <ricardo@pardini.net>
PWM controllable fan (G12A/B/SM1)
Commit provides two new overlays. One for the BananaPi CM4IO
Baseboard "GPIOH_5" and another for general use "GPIOX_5".
CM4IO HEADER PINS: 5V "4"; GND "6"; PWM "7"
On other units the location of the PWM HEADER PIN may vary,
so users will need to either review the wiki or schematic
of said unit.
Fan used in testing:
https://a.co/d/hasnLtj
Modifications: M2S/M5 RTL8822CS
Modded the overlays to be specific to the unit they were made
to be used on.
Tested-on: BananaPi BPI-CM4IO Baseboard with BPI-CM4 Module
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
- general-rc-drivers-should-produce-alternate-pulse-and-space-timing-events.patch: dropped
- added `-spidev` DT's for a few boards (gives access to SPI Flash in exchange for slower eMMC)
- cleanup 0000.patching_config.yaml for meson64-6.7
This does not change the current boot order and requires specific
hardware.
Test-on: BananaPi BPI-CM4IO Baseboard with BPI-CM4 Module
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
