* dts: amlogic: meson-g12b-bananapi-cm4: switch to enable-gpios
The recommended name for enable GPIOs property in regulator-gpio is
enable-gpios. This is also required by bindings:
meson-g12b-bananapi-cm4-cm4io.dtb: regulator-vddio-c: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
* board-bananapi-cm4-switch-to-enable-gpios: `text formatting correction`
Apparently the builder did care for the original.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
---------
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
- using Kwiboo's `rk3568-2023.10` branch with BINMAN-handled blobs
- patches (defconfig unless indicated):
- boot usb first (rockchip-common)
- blink leds & keep red one one on preboot; reset SPI env once after deinfesting from Petitboot
- change usb_host0_xhci to otg (u-boot dtsi)
- enable DM_GADGET, UMS 🔥 and RockUSB
- **usage instructions**:
- build & burn image to SD card
- insert SD card into board
- **hold the recovery (RCY) button** and power on the board
- watch board boot
- **de-infest Petitboot**: use `armbian-install` to install bootloader to MTD
- if you don't, you'll need to hold the recovery button every boot
- optionally: use `armbian-install` to install OS to eMMC/NVMe/USB
- power-off board
- remove SD card (new u-boot always boots SD first!)
- boot into your newly de-infested machine
- boot order: USB, SD, MMC, NVME, SCSI
- de-infested machine can now boot (directly) from USB/SATA/NVMe, possibly via EFI:
- Armbian UEFI-arm64
- Fedora 38 aarch64
- HASSOS for ODROID-M1
- Talos arm64
- others...
- extra: new u-boot by Kwiboo (with GMAC patches) gives us stable MAC address
- although it is based on cpuid#, doesn't match the HK sticker on the board
- run `fw_setenv ethaddr XX:XX:XX:XX:XX:XX` to change eth addr in SPI flash environment if needed
- `odroidm1`: update DDR/BL31 blobs (this depends on https://github.com/armbian/rkbin/pull/20)
Backport DTS/DTSI changes from linux-6.4.y to 6.1.y
Add meson64-reboot driver to all boards
Add board: ODROID N2L
Add uart_A uart_AO_B uart_B uart_C where appropriate
U-Boot v2023.07.02: ODROID N2/N2L/N2Plus/C4
Meson64-reboot driver: (source: tobetter)
While the current meson64-reboot driver is cleaner and doesn't
depend on modding other kernel sources, its functionality leaves
much to be desired. One example can be found in the ODROID C4.
Using the current driver, the board will not properly power off,
leaving the POWER LED still on. The new driver powers off the unit
completely.
Fan control: (ODROID N2L/N2PLus)
Added service and script for controlling the trip point.
fanctrl: arguments: 65 55 45 35 25 menu run
┌──┤ Fan Control ├──┐
│ │
│ 6) 65°C │
│ 5) 55°C │
│ 4) 45°C │
│ 3) 35°C │
│ 2) 25°C │
│ E) Exit .. │
│ │
│ │
│ <Ok> │
│ │
└───────────────────┘
NOTES: (N2L/HC4): I do not own the units so I can't run tests.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
- vim1s/vim4: remove uEnv.txt and default extlinux args, use simple arguments instead
- meson-s4t7.conf: hack: rereadpt (re-read partition table) in initrd local-top (for eMMC boot of oowow'ed image)
- meson-s4t7.conf: include both `u-boot.bin.sd.bin.signed` and `u-boot.bin.signed` in uboot package
- meson-s4t7: patch kernel for different dt "model" across VIM4 and "New VIM4"
- meson-s4t7.conf: set `EXTLINUX_SPECIFIC_FDT=no`, so u-boot auto-determines which DTB to use
- don't specify DTB; this way both the "original VIM4" and the "new VIM4" can boot with the same image
Linux 6.1 (current) / 6.4 (edge)
Add "current" to: config/boards/bananapim2pro.csc
Add uart_AO_B and uart_B to: meson-sm1-bananapi.dtsi
Add related pins to: meson-g12-common.dtsi
add wif/bt support to: meson-sm1-bananapi-m5.dts (BT = uart_A)
Add the ability to enable via overlays
NOTE: The overlay to enable the wifi on the BPI-M5 will be added
at a later date.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
