Those were removed from mainline kernels by Chromebook devs,
wanting to protect their broken babies at all cost.
This patch was dully tested here :
https://forum.armbian.com/topic/13515-panfrost-on-rk3288-and-gpu-on-600mhz-problems/
But you're welcome to test it again !
I did it, with a whole glmark2 round and it worked flawlessly.
To test the GPU at that frequency, locate the **devfreq** folder of your GPU unit on your system (For tinkerboards, it's in **/sys/devices/platform/ffa30000.gpu/devfreq/ffa30000.gpu**) and then :
* Check the available frequencies by doing `sudo cat available_frequencies` .
That should output something like this : `100000000 200000000 300000000 400000000 500000000 600000000`
Be sure that `500000000` is in the list.
* Setup the minimum GPU frequency to 500Mhz like this : `sudo echo 500000000 > min_freq`
You can also set up the GPU to not go over 500Mhz like this : `sudo echo 500000000 > max_freq`
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
* Add initial Helios64 configuration
Add ethernet udev rules
Added disable auto power on script during shutdown
Configure ALSA to output audio to (DisplayPort) USB type-C
armbian-firstrun: exclude helios64 from generating fixed_mac
Each network interface on Helios64 already assigned to unique MAC
address in factory. Assigning Network Manager with cloned MAC is not
needed.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* u-boot: rk3399: Add Helios64
Use rockchip propriettary loader
* kernel: rk3399-legacy: Update r8152 to support 2.5GbE USB RTL8156
Required for Helios64
* kernel: rk3399-legacy: update Rockchip PCIe driver
Port changes by ayufan on rockchip64.
* kernel: rk3399-legacy: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
Auto load lm75 modules
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: rework roc-rk3399-pc patch
the patch broken due to additional line added by helios64 on
arch/arm64/boot/dts/rockchip/Makefile
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rk3399-legacy: update Rockchip PCIe driver
Backport bugfix from mainline
refer to
https://patchwork.kernel.org/patch/11561979/
and
https://patchwork.kernel.org/patch/11561977/
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* kernel: rockchip64-current: Add support for Helios64
Add Helios64 device tree.
Enable missing driver/kernel module.
* config: helios64: use mainline ATF on current branch
and u-boot TPL/SPL instead of Rockchip proprietary loader
* helios64: u-boot v2020.07 update
* Add Helios64 target
* kernel: rk3399-legacy: update Rockchip PCIe driver
Removed unrelated changes from porting ayufan fixes
Signed-off-by: Piotr Szczepanik <piter75@gmail.com>
* helios64: make use of PACKAGE_LIST* variables
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* Add initial support for Odroid N2+
* Update C4 config and test booting
* Updates to C4, N2, N2+
- merge C4 and N2 legacy under meson64, same u-boot
- upgrade legacy kernel to meed DTB from mainline
- merge N2 and N2+, add a hack to display + in motd when N2+ is detected
- shortly spin N2 fan at startup
- merged N2 mainline and legacy boot script
- add upstream patches
* One of the regulators were breaking booting of Odroid N2
Co-authored-by: Werner <EvilOlaf@users.noreply.github.com>
It seems that Charger LED support for AXP20X-like PMICs (AXP813, ...) from Megous is less complete then from Olimex. Reverting the one in the tree and ading the one from Olimex
* Move current to 5.7.x
* Update linux-rockchip-current.config
* Move dev patches to current
* copy dev to current
* move dev patches to current
* move rockchip64-current to 5.7.x
* Add HDMI sound support for Allwinner A10, A20, A31
Closes https://github.com/armbian/build/issues/2084
* Enable HDMI audio in kernel config and update config with misc modules
For some reason these patches are getting applied despite already being in the 5.7 kernel with no complaints from the scripts.
There are more, but it's slow going file by file.
* Bump sunxi to 5.7.y
* Further cleanup 32bit works, 64bit needs more patches adjustement
* Also arm64 boots, SPI flash areas were refactored, new location is a bit fuzzy, leaving behind
* More fixed and cleanings, both variants builds now, but without overlay support
* fix sunxi overlays in AR-329 branch
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Co-authored-by: Martin Ayotte <martinayotte@yahoo.ca>
* Initial commit for kernel boot splash
* Add startup files to disable bootlog when system is up / down
* Update logo, remove deprecated one
* Introduce new u-boot variable bootlogo
* Adjust kernel config
* Make logo possible on Odroid XU4
- add legacy and current upstream patches
- delete xu4 environment since its not used
* Cleanup C2,C4, both tested, logo works on mainline,
- adding legacy upstream patches for c4
* Enable bootlogo by default on Odroid N2
* Enable logo on RK3399 desktop images
* Cleanup the rest of the environment files
* Add initrd hook that copy splash file to initrd.
* Missing logo bits for one boot scripts
* Enable boot logo on Pinebook A64
* Enable bootlogo on Teres
* Update config
* Adjust Rockchip64 dev and add PBPro stuff
* Remove deprecated patches
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Merge config with current
* WIP: Adding RockpiE config
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Mainline u-boot for ROCK Pi E
* Initial ROCK Pi E device tree in kernel
* Fixed supplies for ROCK Pi E device tree
* Adjusted u-boot load address for rockchip64 boards with 256MB eg. ROCK Pi E
* Blacklisted lima on ROCK Pi E
* Fixed ROCK Pi E patch after merge from master
* Removed mode settings from rk805 regulators
* Fixed issues with offloading for gigabit interface of RockPi E
* Adjusted ROCK Pi E board config
* Added dev branch for ROCK Pi E
* Add build targets
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Exchange legacy to current in ROCK Pi E build targets
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* Introducing Rockchip rk322x SoC support
Main features:
- Legacy kernel flavour based upon stable v2.x rk3288 Rockchip branch (https://github.com/rockchip-linux/kernel/tree/stable-4.4-rk3288-linux-v2.x)
- Current kernel flavour based on mainline 5.6.y kernel
- Mainline u-boot (v2020.04)
- Single generic tv box target (rk322x-box) which boots on all the known tv boxes
- Hardware devices (eMMC/NAND, led wiring configuration, SoC variant selection) modulation done by user at runtime via device tree overlays - a script (rk322x-config) is provided for autodetection and simple configuration by inexperienced users;
- Bits added to armbian-hardware-optimization to set affinity for irq handlers
- rk322x-box targets already added to targets.conf for automatic image creation
* Removed disabled patches
* Restored mysteriously removed comment character
* Moved rockchip-dev to kernel 5.7, removed already upstreamed patch (1016), adjusted conflicting patch (1015)
Most kernel configuration answer left at default, notables:
- Wireguard (as module)
- Zswap default compression set to LZO
- RK3288 GPIOMEM (as module)
- Enabled some new DMABUF bits (heaps, cmas)
- Hantro driver
- F2FS compression
* Disabled rx/tx dma for uarts, on my board causes system freeze during bluetooth initialization. Don't know if they ever worked, tried to enable them ages ago and they were already not working
* For xt-q8l-v10 rk3288 board:
- Upgraded u-boot to v2020.04, reworked configuration to match new version, enabled HDMI video console
- Increased u-boot boot delay from 0 seconds to 1 second for rockchip boards, to allow user interrupt u-boot boot process
- Imported efuse rk3288 driver into u-boot, made ethernet address stable using soc serial
- Upgraded ddrbin loader to v1.08
- Added VDSO patch for rockchip-current and rockchip-dev kernels for clock_gettime64 to fix erratic clock on 32 bit ARM devices with recent glibc
- Disabled 600 Mhz OPP node for GPU due to Panfrost instabilities, thus enabled 500 Mhz node
- Various fixes and enhancements to xt-q8l-v10 device trees for current and dev targets
- Added (disabled) u-boot HDMI patch for Tinkerboard
* Removed rk3288 ddrbin v1.08 from rockchip blobs, changed reference to use rkbin-tools repository
* Removed unneeded disabled patch for tinkerboard HDMI
We don't need to enable UARTS and OTG by default on all Nanopi boards. This seems to cause instability on M1
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
NanoPi R2S has the same issue as ROC-RK3328-CC.
With working GPIO, during init the GPIO state s reset.
This causes the sdmmc regulator to shut down, preventing detection.
Removing and replacing the card will allow it to be detected, but that should not be necessary.
Fix this by setting the regulator on at boot.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: 75aa567803
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
* patch: kernel: rockchip-dev: Handle more resolutions with HDMI (β)
The added patch add more PLL configurations, in order to satisfy
more HDMI frequencies requirements.
This should allow users to benefit from more resolutions.
However, this is fairly untested. I only tested it on my 1080p
screen and, yeah, it works but so does the kernel without this
patch.
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
* patch: kernel: rockchip-dev: Handle more resolutions with HDMI (β)
Now with proper patches names.
Anyway :
The added patch add more PLL configurations, in order to satisfy
more HDMI frequencies requirements.
This should allow users to benefit from more resolutions.
However, this is fairly untested. I only tested it on my 1080p
screen and, yeah, it works but it also does without this
patch.
So could anyone test this with the following configurations ?
* [ ] A HDMI 4K screen
* [ ] A HDMI 1366x768 screen resolution
* [ ] A VGA screen with a VGA to HDMI adapter
* [ ] A DVI screen with a DVI to HDMI adapter
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
* Using the patches provided by @Kwiboo for HDMI
This provides me way more resolutions, including interlaced modes.
I don't see 4K modes, though the screen attached can't do it,
so I still don't know if that can help provided 4K modes on mainline
kernels.
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
* Support for 4K screens
Using fixes provided by @czak
Tested and approved by @czak too !
Signed-off-by: Miouyouyou (Myy) <myy@miouyouyou.fr>
There have been intermittent issues with SPDIF output on H3 & H2+ devices.
Digging into the H2+ & H3 datasheets I encountered an important clue on
table 8.7.2.2: s_clk needs to be 4x24.576 MHz or 4x22.5782 Mhz.
Probably due to how SPDIF is a huge oversample of the audio frequency.
Co-authored-by: George Lander <lander@jagmn.com>
* Attach Meson64 CURRENT to 5.6.y and make DEV = CURRENT at this point.
There is a lot of changes to 5.7.y and can be done after release or by someone that feels a need for this right now.
* Delete meson64_fclk_div3.patch
this fix has been upstream for some time, I had issues with it on 5.4, which is why it had been removed there.
* [ meson64 current ] kconfig tweak
disable Rockchip SoC drivers
* [ meson64 current ] remove rockchip patches
* [ meson64 current ] disable CMA patch GX
* [ meson64 current] add libretech cc audio patch
This brings the dts even with the khilman 5.8/integ branch which includes all of the audio changes. The kernel is registering audio devices, however nothing comes out. committed in case someone wants to spend time debugging/testing theories.
* fix permissions
was editing from another machine, accidental change of permissions in the patch
* Set default mixer settings
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* [ meson64 current ] GXL audio commit
This moves to the mainline patches and covers le potato and la frite. Adjusted asound config to handle a commonized sound card name.
* [ meson64 current ] add gxbb audio WIP
Playback is too fast, a clock setting is off somewhere.
* Update kernel configs
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Co-authored-by: Tony <tonymckahan@gmail.com>
* Switching Odroid C1 boot partition to FAT
U-boot FAT driver is very unstable and there is no wish to dig into u-boot. Seems like a sane workaround @plntyk
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Add notes for separate boot partitions
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Typo
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Bugfix: use zImage for converting to uImage since on FAT partitions we use move
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Cleanup C1 boot scripts
We have no plans to ever support legacy kernel again. Removing related things
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* A bit more radical change. Moving meson current to (new) legacy, current to 5.6.y and dev to some development branch / commit.
* Remove unneded patch
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Enable DMC for roc-rk3328-cc (renegade) in current
No stability issues with this enabled, no reason not to merge, enables higher clockrates via manual setting for now.
* enable and change odroidc1 config
remove EOS
enable current and dev config
meson-current: update config
meson-dev: update config
Signed-off-by: Dirk Neukirchen <plntyk.arm@plntyk.name>
* meson-current meson-dev: reduce Kernel size
with default loading locations in u-boot
the uImage can be too large and will be partly overwritten
with the loaded dtb leading to boot failues due to wrong checksum
Signed-off-by: Dirk Neukirchen <plntyk.arm@plntyk.name>
* odroid-c1: change default loglevel
Signed-off-by: Dirk Neukirchen <plntyk.arm@plntyk.name>
* meson: fix odroidc1 boot and create uImage
without uImage the board will not boot
take the already used hack (?) from
general-kernel-odroidn2-current.patch
since KERNEL_IMAGE_TYPE does not work as expected
Signed-off-by: Dirk Neukirchen <plntyk.arm@plntyk.name>
* Update targets.conf
* Update targets.conf
* Update targets.conf
* Making a bigger diff
* Removing build_minimal
One can choose what to build, while build targets are defined elsewhere
* Governor interactive n/a
* Updating config
Cause of changes in boot.ini we don't need to worry about size. After few tests, no problems sighted.
Tested running Docker.
* Adjust dev config too
Tested.
* Update odroidc1.conf
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
deleted activation of i2s1 - 1c2240, because it isnt necessary for the corect operation of audio-analog and sound_hdmi
USB isnt affected.
i2s2 is right, because its needed for sound_hdmi 1c22800
It doesn't want to boot on 5.4.y. Adjusting kernel config, fix Docker dependency problem, move few other minor fixes from openwrt and closing https://github.com/armbian/build/issues/1453
* npi-a64-only-audio-usb.patch
This is a follow-up to the PR #1927 where the complete sun50i-a64.dtsi was changed.
This is a patch ONLY for the NanoPi A64 .dts to activate Audio & Upper USB-port
Has been build/compiled and works with focal 5.6.5
Address = Alias:
sound=sound
sound_hdmi = sound_hdmi
1c19000 = usb_otg
1c22400 = i2s1
1c22c00 = dai
1c22e00 = codec
1c22800 = i2s2
1f015c0 = codec_analog
* Create npi-a64-only-audio-usb.patch
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* meson-sm1: use amlogic-boot-fip to generate boot binary for SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* patch: add Linux and U-Boot patches
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* configs: enable Odroid-C4
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* Add 8189es out of the tree patch from repository.
* Added 8189FS version
* Support building on kernel 5.6. for 88x2bu
Tested for building on legacy, current and dev, removed old patches
* Cleaned up OrangePi 4 device tree (with help from @chwe17)
* Reconfigured OrangePi 4's usb-c power input
* Powertree fixes for OrangePi 4
* Removed unnecessary xin32k clock in OrangePi 4's device tree
* Reverted fusb302 change for OrangePi 4
* Removed uart4 in OrangePi 4's device tree
* Synced OrangePi 4's DTS from current to dev
* Synced OrangePi 4's DTS from current to legacy
* Minor fixups for OrangePi 4 DTS in legacy
* Add initial support for FriendlyARM Nanopi R2s
One net port not working yet.
* Enable 2nd network, rename it to lan0, adjust motd to see lan*
* Added rk3328 dmc devfreq driver
* Fixed SD card issues for NanoPi R2s
* Added usb serial gadget console for NanoPi R2s
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
* [ROCK Pi S] WIP mainline (dev) target
* [ROCK Pi S] Disable `rockchip64-dev` patches for now
* [ROCK Pi S] Add rtl8723ds wifi drivers
* [ROCK Pi S] Enable onboard audio (`rk3308-acodec`,`rk3308-i2s-tdm`)
Switch kernelsource to 5.5.y
* [ROCK Pi S] WIP: Use mainline 5.5.y kernel
Add a new `current` branch that tracks mainline
* [ROCK Pi S] Use updated u-boot board dt name `rk3308-rock-pi-s`
Removing the need for a special bootenv for n
* Temporally disable current
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* kernel: linux-sunxi-{dev,current}: Enable CONFIG_BT_HCIUART_BCM
This patch returns Broadcom's protocol for bluetooth HCI over serial port.
* BananaPiM2Zero: Patches for the devicetree
These patches add HDMI out (with audio) and add bluetooth / wifi
rfkill devices.
* Port ANX78xx Pinebook / Teres LCD panel driver from 5.6-rc1
* Move Teres U-boot to 2020.01 ... it boots with enabled screen now.
* U-boot 2020 needs some extra Pyton utils when packing sunxi bootloader. Adding to native and Docker build dependencies.
* Add Pinebook lid wakeup
* python3-dev is also needed dependency
* [sunxi] allow pcm5102a codec module to be built
for sunxi-current and sunx-dev kernels.
Fixes#1798
* [sunxi] build pcm5102a and pcm51xx_(i2s|spi) modules by default
on sunxi-current and sunxi-dev kernels.
* Added ALSA configuration bits for rk3288 HDMI and SPDIF to allow
pulseaudio show proper sound device/profile/mapping names instead of
just "Built-in Audio" for all of them
* Added ALSA device description in asound.conf to provide correct labels for PulseAudio for RK3288 devices when SPDIF and DW-I2S-HDMI simple audio cards are exposed
Removed unnecessary ALSA configuration files previously added from rockchip.conf
* Fixed cpu operating points tables and raised a bit (+5°C) cooling for non-critical temperatures for xt-q8l-v10 in dev and next kernel flavours
* Fixed again cpu opp table
* Removed whole cpu opp table and retouch only necessary operating points
* Enabled gpiomem driver for xt-q8l-v10 in next kernel flavour
* Added debounce delay and card detect gpio pins for sdmmc card holder for xt-q8l-v10 board
* Added card-detect and debounce delay for sdmmc for xt-q8l-v10 board in next kernel flavour too
* Fixed missing comment in xt-q8l-v10 device tree patch
* Added gpiomem to xt-q8l-v10 board for dev kernel
* Fixed FAN53555/Silergy patches to accomodate changes in u-boot v2019.04
* Changed property property flags for USB regulators in u-boot and kernel: kernel is now informed that bootloader is going to turn the USB power on
* Fixed indentation in rk3288-xt-q8l-v10.dts, raised debounce delay to sdmmc, added vbus-supply to USB host, removed some unneeded properties
* Added working DDR52 mode for eMMC on xt-q8l-v10
* Removed regulator-off-in-suspend for some xt-q8l-v10 regulators due to changed in act8865.c driver which causes the regulators to be misconfigured
* Adjusted targets for xt-q8l-v10 (provides bionic desktop + buster server)
* Removed all regular-state-mem nodes in xt-q8l-v10 device tree because the change in act8865.c affects also non-off entries
* Brought xt-q8l-v10 device tree from rockchip-current to rockchip-dev
Adds k5.5 audio pipeline dts entries, adds audio to Renegade, cleans up some dts mess in renegade
- Note: PulseAudio seems to need to toggle a couple times before audio will play. That is not addressed in this patch.
* Add exceptions to support native Ubuntu 20.04 building, fix small bug related to SD card write verification.
* Improve first install steps by installing Dialog and lsb_release first. This left out since we moved host install after we choose what we will do ... dialog is essential for this. Second we don't wait properly for APT manager to finish the process. Fixed with this commit
* Suppress output
* Update OdroidXU4 dev config & patches
* Attach Meson64 to mainline with a bunch of patches. Tested, but need further work.
* Enable DVFS on N2 which sometimes works, sometime doesn't, cleanup
* Enable beta targets for Meson64 kernel family
* Bump with version
* Fix cpufreq (dynamic frequency scaling) for mvebu-current. Also move disabled patches in extra folder for better usability
* Move unlock-atheros-reg patch to disabled
* Accidentally deleted a patch instead of moving it to disabled. Restore it
* Survived standard stress testing + one night of normal operation (Helios4)
* Wireguard: bump tag to most recent since it breaks building on 5.4.y
* Move rockchip current to 5.4.y
* Move sunxi current to 5.4.y
* Move meson64 to 5.4.y
* Move odroidxu4 to 5.4.y and enable "current" targets
* Enable missing target
this update of the previous patch (#1663) additionally fixes the following overlays:
sun5i-a13: i2c1..2, nand, pwm, spi2, uart0..3
sun4i-a10: can, i2c1..2, pwm, spdif-out, spi0..2
corrections re #1663:
sun7i-a20: fixed typo in pwm overlay in #1663
arch64-makefile now back in line with original patch
this update of the previous patch (#1663) additionally fixes the following overlays:
sun5i-a13: i2c1..2, nand, pwm, spi2, uart0..3
sun4i-a10: can, i2c1..2, pwm, spdif-out, spi0..2
corrections re #1663:
sun7i-a20: fixed typo in pwm overlay in #1663
arch64-makefile now back in line with original patch
some armbian dts overlays currently do not work since pinctrl names have not been
adapted to renaming in 5.0 and 5.2.
this patch modifies the following overlays:
sun50i-h5: cir, spdif-out
sun8i-h3: cir, spdif-out
sun7i-a20: i2c1..4, mmc2, pwm, spdif-out, spi0..2, spi-add-cs1, uart4..7
sun5i-a13: uart0
sun4i-a10: spdif-out
some armbian dts overlays currently do not work since pinctrl names have not been
adapted to renaming in 5.0 and 5.2.
this patch modifies the following overlays:
sun50i-h5: cir, spdif-out
sun8i-h3: cir, spdif-out
sun7i-a20: i2c1..4, mmc2, pwm, spdif-out, spi0..2, spi-add-cs1, uart4..7
sun5i-a13: uart0
sun4i-a10: spdif-out
* Sunvell R69: cpu voltage regulator (re-)added - dram clock reduced.
CPU regulator (re-)added to u-boot and kernel dts - the box will not boot without it.
Dram clock reduced in defconfig to increase stability.
[AR-85]
* Updated rockchip64-dev to u-boot v2019.10 and BL31 v1.30 (rk3399 boards)
* Updated rk3399 to u-boot v2019.10 and BL31 v1.30
* Revert changes to renegade u-boot patches
* Moved renegade u-boot patches into board dir
* Added debug info for RockPro64 and switched sdmmc to fifo-mode
* Disabled regulators in SPL for RockPro64
* Re-enabled sd vcc regulator in SPL for RockPro64
* Some device tree and config changes for OrangePi RK3399
* Fixed Rock Pi 4A's $BOOTCONFIG
* Let some boards use mainline atf instead of the one in rkbin
For example, roc-rk3399-pc can just boot the kernel using the
mainline atf.
* Add roc-rk3399-pc
* Fixed reset in mainline ATF
* Attached ATF version to v2.2 tag
* WIP: sdmmc fifo-mode in SPL only
* Renamed source config files
* Reverted changes to rockchip64 sources config
* Reverted patch moves
* Add missing trust.ini patch to rk3399 u-boot
* Reinstated tpl/spl patches in rk3399 family
* Added $RKBIN_DIR prefix in rk3399 sources
* Add demonstration of boards bootloader assignment in rk3399
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
* Fix wifi
patch "board-h2plus-nanopi-duo-add-device.patch": increase post-power-on-delay-ms from 50ms to 200ms in wifi_pwrseq node in nanopi-duo dts [dev-branch].
Change in line with other XRADIO device trees (orange pi zero, sunvell).
See also Pull Request #1605.
* Fix xradio patch (dev-branch)
fix KConfig to 5.x - WLAN_VENDOR-flag set to "y" in line with other drivers - otherwise module not loaded.
* correct device name
change nodes "model" and "compatible" to correct device name (from "NanoPi Duo AIR" to "NanoPi Duo") [dev-branch]
Not functionally necessary, but more correct.
U-Boot already support device tree overlay. However, it requires the
base dtb to be compiled with __symbol__ support.
This commit added patches to compile dtb with required parameter.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* UPSTREAM: media: rc: rename RC_TYPE_* to RC_PROTO_* and RC_BIT_* to RC_PROTO_BIT_*
Realigned the source code to the RC_TYPE* / RC_BIT_* refactoring
* Restored the inclusion of the DVB-USB dib0700 driver
Adjust configuration, merge with general purpose armv7 Fedora kernel, remove deprecated patch, move coherent_pool and cma to boot script
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
atomic_pool_size can be controlled by kernel cmdline,
coherent_pool=nn[KMG] [ARM,KNL]
then use this parameter to replace the patch.
Signed-off-by: Zhang Ning <832666+zhangn1985@users.noreply.github.com>
* Initial commit for serial consoles rfc
* Board configuration cleanup + small tweaks
* Add serial gadget rename to dev kernel as well
* Cleanup, fixing permissions
* Cleanup board configs
due to modpost is used by dkms or out-of-tree kernel modules, eg mali
so add this tool to linux-header's postinst script
for #1552
Signed-off-by: Zhang Ning <832666+zhangn1985@users.noreply.github.com>
* Initial commit for FA ZeroPi.
* Tested for building.
* Adjust few bugs.
* Move to WIP since its not tested on hardware yet.
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Added initial support of MCIMX7SABRE board
MCIMX7SABRE is NXP iMX7d-based board with 1Gb RAM
2xGBE, 1xmPCIe
Change-Id: I62685a55de54fa6109bef2a8e2ee760d831ffa0e
* Changed BOARDFAMILY from mx7dsabre to imx7d
Change-Id: Id351c9f6a8c907b415b804bfe11b86027278ed86
* Disabled MD driver for imx7d Kernel
MD driver does not work correctly on NXP-modified kernel
Change-Id: I58e8de6ee0b99282c452f594e22f6f7e1ff59ae0
* Introducing build-all-ng
* Implementing REBUILD_IMAGES='board1,board2,...' for rebuilding certain images only
* Add optimisations when building kernels - only cycle trough needed targets. Adding variable for defining whether an image is build, otherwise only BSP is made.
* repository manipulating RFC
* Add bianco deb file that is added by default if repository is clean
* Switch to gpg2 signing method, small bugfix
* Create subdir for debs and debs-beta
* Synaptic bugfix: installing indexing tools https://forum.armbian.com/topic/8021-orange-pi-one-synaptic-package-manager-search-very-slow/?do=findComment&comment=74918
* add all modules by default to Odroid N2, but leave them commented
* Bugfix: not making any builds when selecting kernel_only
* Remove EXTERNAL=yes ... move armbian-config and armbian-firmware into main compilation area, drop others since they are deprecated anyway. This will also enable multi threaded images making
* Move armbian.list to create_sources_list function. Replace NTP by Chrony. Remove armbian-firmware from PACKAGE_LIST and RockPi 4A (#1528)
* Replace NTP by chrony. Remove installion of outdated armbian-firmware from reposity.
* added RockPi 4A
* New format for board config
* Fix Bluetooth dependencies for minimal package - add rfkill to family related installs
* Moving networkd-dispatcher from minimal image
* Cubox-i: update default config
* Improving umount process
* Add purgesource feature
* Add FULL_DESKTOP to install few more applications on top of our desktop - notebooks should * rk3399 default: adjust patches and configuration
* Enable full desktop on most powerfull boards and notebooks
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Added ALSA configuration bits for rk3288 HDMI and SPDIF to allow
pulseaudio show proper sound device/profile/mapping names instead of
just "Built-in Audio" for all of them
* Added ALSA device description in asound.conf to provide correct labels for PulseAudio for RK3288 devices when SPDIF and DW-I2S-HDMI simple audio cards are exposed
Removed unnecessary ALSA configuration files previously added from rockchip.conf
* Fixed cpu operating points tables and raised a bit (+5°C) cooling for non-critical temperatures for xt-q8l-v10 in dev and next kernel flavours
* Fixed again cpu opp table
* Removed whole cpu opp table and retouch only necessary operating points
* Enabled gpiomem driver for xt-q8l-v10 in next kernel flavour
* Added debounce delay and card detect gpio pins for sdmmc card holder for xt-q8l-v10 board
* Added card-detect and debounce delay for sdmmc for xt-q8l-v10 board in next kernel flavour too
* Fixed missing comment in xt-q8l-v10 device tree patch
* Added gpiomem to xt-q8l-v10 board for dev kernel
* Fixed FAN53555/Silergy patches to accomodate changes in u-boot v2019.04
* Changed property property flags for USB regulators in u-boot and kernel: kernel is now informed that bootloader is going to turn the USB power on
* Removed assert-phy-reset-when-waking-up-in-rk3288-platform patch due to inclusion in mainline 5.2 kernel
Reenabled ARM-DTSI-rk3288-add-usbphy-reset patch to include USB PHY reset lines to all rk3288 devices
* Removed ARM-DTSI-rk3288-add-usbphy-reset.patch due to inclusion in mainline kernel 5.2
* Attached cubox-i to stock kernel. Tested. Sadly ZRAM has some issues, so it must ramain disabled
* more imx6 updates for cubox/udoo
* Enable HDMI on Cubox-i
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
1, format all patches from https://github.com/megous/linux
`git format-patch 79bf89b88a87f2ebf147f76d8c40183283b49b51...2a7cb228d29c3882c1414c10a44c5f3f59bfa44d`
and copy them to sunxi-next with prefix `0000-`
2, remove unnecessary patches, due to they are revert of upstream patches:
4d867e2bd64e674a3000b8e05fe47e8bb8175edda2888276ee
3, remove fail to apply and no use:
960ddd63a8
4, remove WireGuard patch:
1cd13b836c
5, remove meaningless patch:
f26e36379a
6, remove merged or included by megous/linux patches:
0112-mfd-axp20x-Add-supported-cells-for-AXP803.patch
board-bpi-m3-make-ethernet-working.patch
board-pine-h6-pine-h6-0025-phy-sun4i-usb-add-support-for-missing-USB-PHY-index.patch
7, remove stable release update patches.
ignored.
8, rebase sunxi-next/sunxi64-next to upstream linux-4.19.y
test result:
all patches applied, no error.
orangepipc/orangpioneplus build OK.
Signed-off-by: Zhang Ning <832666+zhangn1985@users.noreply.github.com>
In current kernels (both next and dev) this patch breaks cpufreq and all that depends on it (no dvfs means board overheating). Removing it makes cpufreq and dvfs work again.
* fix kernelcrash with config_of_overlay combined with isp1 camera driver,based on:
30a8401c2f
* add basic dtbo infrastucture
* set ov5647 (RPi cam rev 1.3) as default, imx219 (RPi cam V2.1) outputs a blurry green videostream at the moment
* maybe fix powering for camera
* adjust mainline dtbo patch to bsp kernel
* got you! little.. dtbo's are properly built and applied during boot.
* add imx219 overlay to switch between cameras & add ae/awb fix for ov 5647 from asus tinker repo
* patch imx219 up to 96396323fa
* bring back wireguard, otherwise igor gets grumpy :D
* fix camera status
