* Rockchip64 Linux-5.10y - drivers for Motorcomm YT8531
renamed the previous "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" to "net-phy-Add-driver-for-Motorcomm-1-YT85xx-PHYs.patch" to fix patch order and added a new patch "net-phy-Add-driver-for-Motorcomm-2-YT8531-PHYs.patch"
The new YT8531 patch is sourced from from Lean's OpenWrt source rockchip/patches-5.10/601-net-phy-Add-driver-for-Motorcomm-YT8531-PHYs.patch.
It is intended to extend a patch identical to Armbian's "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" and is used without alteration.
* Add new board OrangePi R1 LTS (rk3328)
Includes uBoot and support for Linux-5.10y
* Rockchip64 Linux-5.15y drivers for YT8531 and other Motorcomm chips
YT8010, YT8510, YT8511, YT8512, YT8521. The driver patch set is sourced from Xunlong-OrangePi OpenWRT and is used as is, with only a name and makefile change.
A single patch set uses the same underlying source code as the Armbian Linux-5.10y set, but uses inbuilt logic to apply tweaks that depend on the Linux kernel version.
The patch is renamed similarly to the 5.10 patch set, net-phy-Add-driver-for-Motorcomm-T85xx+PHYs.patch to imply code base continuity with the previous similar Armbian patch sets.
* Rockchip64 Linux-5.15y support for Orange Pi R1 Plus LTS
Includes DTS and makefile changes. A driver for net phy YT8531C is in a separate commit
* change orangepi-r1plus-lts.csc to orangepi-r1plus-lts.conf
board is now supported
* - add patch also to 5.16.y
- fix wrong patch permission
* Fix Makefile patch
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Radxa Zero 2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
* Bump Meson64 u-boot to 2022.01
Tested VIM boards
* Move Jethub related patches under common meson64 patch collection
* Move jethub patch to per board and remove unneded settings
* Sync kernel config with radxa and remove packaging patch
* Merge the rockchip64 legacy config as well
* Lower priority of EFI partitioning against DOS partitioning which is used by Armbian
Co-authored-by: Catalin Toda <catalinii@yahoo.com>
* JetHome: Update u-boot patches: fix emmc work on JetHub D1
* JetHome: update kernel patches with last updates for JetHub devices.
* JetHome: Update Bluetooth init script to more stable start.
* Switched rockchip64 u-boot to v2021.07
* Switched OrangePi R1 Plus to include mainline's R2S device tree
* Added unsingned signed comparison patch from Paolo to fix rk3328 reboots
* Bugfix - Bananapi PRO seems to work fine with latest u-boot
Done many reboots and it didn't break. The same has to be tested with other A20 boards
* Set Allwinner 32bit hw to most recent u-boot 2021.07
* Let's move all to 2021.07 and test ...
* meson64: bump u-boot to 2021.07, rework patches
- as always based on chewitt's tree, with differences:
- squashed versions of HC4+SATA, Radxa Zero, DT tree sync patches
- so that DTB/config/code changes related to the same feature/board are grouped
- removed documentation changes and Makefile reordering patches
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* meson64: ODROID HC4/N2: simplify/remove board vs family hacks; better SPI support
- thanks to mainline 2021.07 u-boot and it's HC4 config we can remove the conditionals
- boards now define the u-boot vars instead of conditionals in family
- on the HC4, build u-boot twice: one for SD (old C4 config) and one for HC4 (new SATA/SPI config)
- reason is that the HC4 version does not work very well unless it is actually booted from SPI
- meson64_common: don't override UBOOT_TARGET_MAP if board-defined
- but the default UBOOT_TARGET_MAP is still defined if the board didn't
- (sneakily) add lm-sensors fancontrol to the HC4's board packages
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Add support for Radxa Zero
u-boot: new patch based on v2021.04
kernel: use patches sent to kernel list by chewitt
Tested with minimal build and cinnamon desktop:
- SD/eMMC, ok
- USB3, works in USB 2 mode
- HDMI, ok
- WiFi/BT, ok
Signed-off-by: Jack Ma <jack@radxa.com>
* Add build targets
* Cleanup and set min speed to 666000
* Change to WIP target
Support status undetermined
Co-authored-by: Jack Ma <jack@radxa.com>
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
* Fixed u-boot script and kernel config for i.MX7D
Fixed bug in u-boot script preventing to use armbianEnv.txt
Configured SDMA as module to fix loading SDMA firmware
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* remove obsolete and broken patch for pine64so u-boot
This prevents the image from being built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: fix pine64so phy-mode and add yt8511 support
Pine A64-LTS board should have RGMII-TXID mode instead of RGMII-ID (the
Realtek PHY chip's RXID is sometimes broken).
In addition, new Pine A64-LTS v2 board will use YT8511 instead of
RTL8211E, which still works under RGMII-TXID mode.
Backport YT8511 driver and phy-mode change from linux-next.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-audio-codec-bpim2ultra-kernel.patch
- Add patch to enable audio codec in bpi-m2-ultra with h3 compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
* Bump imx6 edge to 5.12.y
* Bump odroid xu4 edge to 5.12.y
* Bump Jetson nano edge to 5.12.y
* WIP: Bump sunxi to 5.12.y
- create a copy of patches and make a new link
- wireless patches needs adjutement to 5.12
- some patches are still failing
* Adjust wireless patches to build on 5.12.y
* Remove template wireless patch
* Move Espressobin edge to 5.12.y
* Bump mvebu to 5.12
- patch 92-mvebu-gpio-remove-hardcoded-timer-assignment.patch was disabled @heisath
- adjusted wireless driver for 8723ds
* Adjust sunxi / sunxi64 edge to compile
* Fix kernel config for Jetson nano edge
* bump meson64 to 5.12.y
* bump rockchip edge to 5.12.y
* Bump rockchip64 to 5.12.y
* Bump rk322x edge to 5.12.y
@paolosabatino
* Cleanup im6, re-add 5.10.y patches since one is missing in 5.12.y
* Update odroidxu4 edge links
* rk322x: moved rk322x-edge to kernel 5.12, fix overlay compilation, retouched included kernel modules
* Cleanup: remove deprecated config
Co-authored-by: Paolo Sabatino <paolo.sabatino@gmail.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-sound-pinecube-kernel.patch
- Add patch to enable audio codec in pinecube with v3s compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
