This gives the rich OS the flexibility to choose between I2C and RSB
communication. Since a runtime address can only be assigned once after
entering RSB mode, it also lets the rich OS choose any runtime address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id49c124c5e925985fc31c0ba38c7fb6c941aafa8
None of the other drivers (Linux, U-Boot, Crust) need to lower the bus
clock frequency to switch the PMIC to RSB mode. That logic is not needed
here, either. The hardware takes care of running this transaction at the
correct bus frequency.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Idcfe933df4da75d5fd5a4f3e362da40ac26bdad1
BL31 reports the following warning during boot:
WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!
Resolve this by enabling the workaround on the affected platforms.
Change-Id: Ia1d5075370be5ae67b7bece96ec0069d9692b14c
Signed-off-by: Samuel Holland <samuel@sholland.org>
While the Allwinner platform code nominally supported a custom
PRELOADED_BL33_BASE, some references to the BL33 load address used
another constant: PLAT_SUNXI_NS_IMAGE_OFFSET. To allow the DTB search
code to work if a U-Boot BL33 is loaded to a custom address,
consistently use PRELOADED_BL33_BASE. And to avoid this confusion in
the future, remove the other constant.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie6b97ae1fdec95d784676aef39200bef161471b0
The H6 has a "secure port controller" similar to the A64/H5, but with
more ports and a different register layout. Split the platform-specific
parts out into a header, and add the missing MMIO base address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I3703868bc595459ecf9568b9d1605cb1be014bf5
H6 has a reorganized R_PRCM compared to A64/H5, with the security switch
at a different offset. Until now, we did not notice, because the switch
has no effect unless the secure mode e-fuse is blown.
Since we are adding more platform-specific CCU registers, move them to
their own header, and out of the memory map (where they do not belong).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie77476db0515080954eaa2e32bf6c3de657cda86
* changes:
doc: Update list of supported FVP platforms
board/rdn2: add board support for rdn2 platform
plat/arm/sgi: adapt to changes in memory map
plat/arm/sgi: add platform id value for rdn2 platform
plat/arm/sgi: platform definitions for upcoming platforms
plat/arm/sgi: refactor header file inclusions
plat/arm/sgi: refactor the inclusion of memory mapping
This patch disable the ITAPDLYENA bit for ITAP delay value zero.
As per IP design, it is recommended to disable the ITAPDLYENA bit
before auto-tuning.
Also disable OTAPDLYENA bit always as there is one issue in RTL
where SD0_OTAPDLYENA has been wrongly connected to both SD0 and SD1
controllers. Hence it is recommended to disable OTAPDLYENA bit always
for both the controllers.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Icf035cb63510ac7bec4e9d523a622f145eaf0989
This patch check for the DLL status before doing the DLL reset.
If DLL reset is already issued then skip the reset inside ATF
otherwise DLL reset will be issued.
By doing this way, all the following cases will be supported.
1. Patched ATF + Patched Linux base.
2. Older ATF + Patched Linux base.
3. Patched ATF + Older Linux base.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I53a0a27521330f1543275cc9cb44cd1dfc569c65
* changes:
plat: xilinx: versal: Add support of register notifier
plat: xilinx: versal: Add support to get clock rate value
plat: xilinx: versal: Add support of set max latency for the device
plat: versal: Add InitFinalize API call
xilinx: versal: Updated Response of QueryData API call
plat:xilinx:versal: Use defaults when PDI is without sw partitions
plat: xilinx: Mask unnecessary bytes of return error code
xilinx: versal: Skip store/restore of GIC during CPU idle
plat: versal: Update API list in feature check
xilinx: versal: Do not pass ACPU0 always in set_wakeup_source()
* changes:
spm: provide number of vCPUs and VM size for first SP
spm: remove chosen node from SPMC manifests
spm: move OP-TEE SP manifest DTS to FVP platform
spm: update OP-TEE SP manifest with device-regions node
spm: remove device-memory node from SPMC manifests
Add the initial board support for RD-N2 platform.
Change-Id: I8325885bf248dd92191d6fc92a2da91c23118f8c
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Upcoming RD platforms will have an updated memory map for the various
pheripherals on the system. So, for the newer platforms, handle the
memory mapping and other platform specific functionality separately
from the existing platforms.
Change-Id: Iab1355a4c8ea1f6db4f79fcdd6eed907903b6a18
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
In preparation for adding the board support for RD-N2 platform, add
macros to define the platform id and the corresponding SCMI platform
info for the RD-N2 platform.
Change-Id: Ie764ae618732b39e316f7ed080421f5d79adab21
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Upcoming RD platforms have changes in the SOC address map from that
of the existing platforms. As a prepartory step to add support for the
upcoming platforms, create platform definitions for those platforms.
Change-Id: Ic5df9fed02c44e65ec260bbb5efc1b8dbd919a56
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Upcoming RD platforms have deviations in various definitions of
platform macros from that of the exisiting platforms. In preparation
for adding support for those upcoming RD platforms, refactor the
header file inclusion to allow newer platforms to use a different
set of platform macros.
Change-Id: Ic80283ddadafaa7f766f300652cb0d4e507efdb6
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Upcoming RD platforms have a different memory map from those of the
existing platforms. So make the build of the existing mmap entries to be
usable only for existing platforms and let upcoming platforms define
a different set of mmap entries.
Change-Id: Id1ef0293efe8749c78a99237e78d32573c7233aa
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Current implementation doesn't support change of div1 value if clk
has 2 divisor because div1 clk is the parent of the div2 clk and div2
clk does not have SET_RATE_PARENT flag.
This causes div1 value to be fixed and only value of div2 will be
adjusted according to required clock rate.
Example:
Consider a case of nand_ref clock which has 2 divisor and 1 mux.
The frequency of mux clock is 1500MHz and default value of div1 and
div2 is 15 and 1 respectively. So the final clock will be of 100MHz.
When driver requests 80MHz for nand_ref clock, clock framework will
adjust the div2 value to 1 (setting div2 value 2 results final clock
to 50MHz which is more inaccurate compare to 100Mhz) which results
final clock to 100MHz.
Ideally the value of div1 and div2 should be updated to 19 and 1
respectively so that final clock goes to around 78MHz.
This patch fixes above problem by allowing change in div1 value.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ibb98f6748d28653fdd1e59bf433b6a37ce9c1a58
This patches copies only the valid part of string and
avoids filling junk at the end.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If23772f31f9cf7f5042e8bfc474fbfe77dcd90e7
The primary VM concept is removed from the SPMC.
Update the SPMC manifests with number of Execution Contexts
and SP workspace size for the first Secure Partition (as it
is done for NWd secondary VMs and other SPs).
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I3b9c52666f7dfe74ab1f7d2148ad0070ee44b54e
The chosen node is no longer required as the SPMC implements
a specific boot flow which no longer requires this node.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: Ib566b602a7f83003a1b2d0ba5f6ebf4d8b7a9156
The PVM concept is removed from the SPMC so the device-memory
node which is specifying the device memory range for the PVM
is no longer applicable.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: If0cb956e0197028b24ecb78952c66ec454904516
When system resume, we want to print log as soon as possible.
So we add uart save and restore api, and they will be called
when systtem suspend and resume.
Change-Id: I83b477fd2b39567c9c6b70534ef186993f7053ae
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.com>
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
1.Modify this driver to make it more complete and more standard.
2.And makes this driver available for more IC services.
3.Solve some bugs in the software.
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I284956d47ebbbd550ec93767679181185e442348
Implement PSCI platform OPs to support CPU hotplug and MCDI.
Change-Id: I31abfc752b69ac40e70bc9e7a55163eb39776c44
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Add MCDI related drivers to handle CPU powered on/off in CPU suspend.
Change-Id: I5110461e8eef86f8383b45f197ec5cb10dbfeb3e
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Add support of register notifier.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I41ef4c63abcc9aee552790b843adb25a5fd0c23e
Add support to get clock's rate value.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I3ed881053ef323b2ca73e13edd0affda860d381d
Add support of set max latency, to change in the maximum powerup latency
requirements for a specific device currently used by Subsystem.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I8749886abb1a7884a42c4d156d89c9cd562a5b1a
Add support to call InitFinalize API in Versal which calls
corresponding LibPM API.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I3428b7245b4db1ef6db8a90b7ad20b6e484ed3b2
For the current XilPM calls, The handler of IPI returns information
with 16 Bytes data.
So during QueryData API call for the ClockName and PinFunctionName,
response data(name of clock or function) response[0..3] are used to
return name. And status is not being returned for such API.
Updated XilPM calls reply in a consistent way and The handler of IPI
return information with 32Bytes data. Where response[0] always set
to status.
For the version-2 of QueryData API, during call for the ClockName
and PinFunctionName, response data(name of clock or function) get as
response[1...4].
To support both the version of QueryData API, added version based
compatibility by the use of feature check.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Amit Sunil Dhamne <amit.sunil.dhamne@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I336128bff7bbe659903b0f8ce20ae6da7e3b51b4
In JTAG mode check the ATF handoff structure, if the magic string
is not present then use bl32 and bl33 default values.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I1f2c4a2060d8a2e70d3b5fb2473124b685f257fc
Versal firmware adds extra error codes along with PM error codes
while sending response to driver. This makes incorrect error
identification at driver side.
To fix this, mask the unnecessary error bytes before sending the
error code to the driver.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I18c2f3bd2d067e91344852c2f0c1bafea0e6eb23
GIC registers needs to be stored/restored during system
suspend/resume only and not during CPU idle.
During CPU idle, minimum 1 CPU is in ON state.
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I5de2ce3a61bf4260f9385349202b0f592a47aaba
Add below API in feature check list which is actually present in
firmware:
- PM_GET_CHIPID
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I98b82da74164f065c8835861f74b0f2855e9bcbf
Existing code passes ACPU0 to LibPM as node_id in set_wakeup_source()
call because last suspending core will be ACPU0 in most of the case.
Now it may be possible that user may disable the ACPU0 using hot-plug
and after that it suspends Linux. So in that case ACPU0 will not be
last suspending core.
To overcome above scenario, pass the current running processor ID
while calling set_wakeup_source().
Signed-off-by: Ravi Patel <ravi.patel@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: If15354c2150b5bb1305b5f93ca4e8c7a81d59f0a
These two targets are build by make subprocesses and are independent.
So splitting them into own targets allow make to build them in parallel.
$(TIMBUILD) script depends on $(TIMDDRTOOL) so specify it in Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I139fc7fe64d8de275b01a853e15bfb88c4ff840d
Add check when building mrvl_bootimage that size of bl1 image is not bigger
than maximal size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ib873debd3cfdba9acd4c168ee37edab3032e9f25
